ASTM D1200 PDF

ASTM D – Designation: D – 10 Standard Test Method for Viscosity by Ford Viscosity. ASTM D Standard Test Method for Viscosity by Ford Viscosity Cup. mm (˝) Orifice diameter; 25 – cSt Viscosity range; 40 – sec. Flow times. Viscometer Flow Cup, ASTM D, Ford No 3 · Viscometer Flow Cup.

Author: Kaganos Meztigul
Country: Botswana
Language: English (Spanish)
Genre: Video
Published (Last): 17 September 2017
Pages: 10
PDF File Size: 6.21 Mb
ePub File Size: 3.10 Mb
ISBN: 651-5-18472-926-5
Downloads: 95728
Price: Free* [*Free Regsitration Required]
Uploader: Shaktijas

The preferred method is to over? This standard has been approved for use by agencies of the Department of Defense.

For particular oils applicable for use with the Ford Cups refer to Table X1. Fill the cup with x1200 prepared specimen. Box 16, State College, Pa.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. NOTE 2— It is impossible to predict the effect of temperature change on each material with which the apparatus may be used.

Last previous edition approved in as D — 94 It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Under no conditions should metal cleaning tools be brought into contact with the instrument. Bring this cup and the liquid viscosity standard to a constant temperature as close as possible to Determinations should be made at a temperature above the dew point of the atmosphere surrounding the apparatus. Temperature drift during the test should be kept to a minimum and should not exceed Oils available from other sources, having known kinematic viscosities, may also be used.

  GUILLAIN BARRE VARIEDAD MILLER FISHER PDF

In addition, temperature measuring devices such as non-mercury liquid-in-glass thermometers, thermocouples, or platinum resistance thermometers that provide equivalent or better accuracy and precision, that cover the temperature range for thermometer 17C and 17F, may be used.

Originally approved in Summary of Test Method 4. Particular care must be exercised in cleaning the ori?

Keep the temperature drift to within The values given in parentheses are for information only. NOTE 1—If d12200 ori? Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

ASTM D | Hanatek Instruments

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Awtm and Bias A percent correction can be applied to the seconds? Care of Cup Calibration Procedure for Ford Cups X1.

Determine the time of efflux to the nearest 0. If the material is non-Newtonian, that is, shear-thinning or thixotropic, Test Method D should be used. The frequency of this calibration check depends upon the amount of use and the care that the individual cup receives.

  JAYAKIRANA NEWS PAPER PDF

Allow to stand undisturbed for 10 min while adjusting further to the desired temperature. A number in parentheses indicates the year of last reapproval.

ASTM D – 10() Standard Test Method for Viscosity by Ford Viscosity Cup

Measure the time until the? A small change in diameter of the ori? Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or d12000 phonefaxor service astm. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

ASTM D 2.

ASTM D1200

Permission rights to photocopy the standard may also be secured from the ASTM website www. Current edition approved July 1, Qstm of Testing 8. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Pull the stopper away and simultaneously start the timing device. Make the viscosity determination at the end of the min period. If the ratio of shear stress to shear rate is not constant, the liquid is nonNewtonian.