ASTM E8 E8M PDF

AHM E8/E8M – 13a. G–Gauge length. Dimensions, mm [in.] For Test Specimens with Gauge Length Four times the Diameter (E8]. Standard. Small-Size. Buy ASTM E 8/E8M: A TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS from SAI Global. Originally contact ASTM Customer Service at [email protected] For Annual Book of ASTM approved in Last previous edition approved as E8/ E8M.

Author: Gujas Tucage
Country: Djibouti
Language: English (Spanish)
Genre: Travel
Published (Last): 21 May 2018
Pages: 187
PDF File Size: 11.49 Mb
ePub File Size: 6.32 Mb
ISBN: 999-7-86024-976-6
Downloads: 32060
Price: Free* [*Free Regsitration Required]
Uploader: Mauzragore

These wedge grips generally furnish a satisfactory means of gripping long specimens of ductile metal.

When liners are used behind the wedges, they must be of the same thickness and their faces must be flat and parallel. C39M – 16 – Compressive Strength of Cylindrical This information may be useful in comparisons of materials, alloy development, quality control, and design under certain circumstances.

Extensometers shall be used and verified to include the strains corresponding to the yield strength and elongation w8 fracture if determined. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Both of these gripping devices should be attached to the aetm of the testing machine through properly lubricated sphericalseated bearings.

For a standard A number in parentheses indicates the year of last reapproval.

ASTM E8 / E8M – 13 Standard Test Methods for Tension Testing of Metallic Materials

Originally approved in It is important, therefore, that care be exercised in the preparation of specimens, particularly in the machining, to maximize precision and minimize bias in test results.

  HONEYWELL HD73 PDF

If, however, for any reason, one grip of a pair advances farther than the other as the grips tighten, an undesirable bending stress may be introduced. Parte 1 de 8 Designation: A superscript epsilon indicates an editorial change since the last revision or reapproval. E8M Tensiont testing of metallic materials Juliano row Enviado por: The gauge length is the most significant difference between E8 and E8M test specimens.

Any departure from this 8e may introduce bending stresses that are not included in the usual stress computation force divided by cross-sectional area. For this reason, a small taper is permitted in the reduced section of each of the specimens described in the following sections. For best results, the wedges should be supported over their entire lengths by the heads of the testing machine. Proper alignment of wedge grips and liners is illustrated in Fig. This error increases to 2.

Current edition approved May 1, For measuring elongation at fracture with an appropriate extensometer, the e8k length of the extensometer shall be equal to the nominal gauge length required for the specimen being tested. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM E8.E8M Tensiont testing of metallic materials –

To ensure axial tensile stress within the gauge length, the axis of the test specimen should coincide with the center line of the heads of the ee8 machine. NOTE 1—The effect of this eccentric force application may be illustrated by calculating the bending moment and stress thus added.

  FUQIN XIONG DIGITAL MODULATION TECHNIQUES PDF

Astm c astm normas fibra de vidrio. For short specimens and for specimens of many materials it is aetm necessary to use machined test specimens and to use a special means of gripping to ensure that the specimens, when under load, shall be as nearly as possible in uniformly distributed pure axial tension see 5.

The distance between spherical bearings should be as great as feasible. The test methods have been used extensively in the trade for this purpose.

ASTM E8.E8M -15-Tensiont testing of metallic materials

The forces used in e88 tensile strength and yield strength shall be within the verified force application range of the testing machine as defined in Practices E4.

Such interpretation is usually applicable to values for reduction of area reported in the literature when no further qualification is given.

Astm a Astm a NOTE 3—Punching or blanking of the reduced section may produce significant cold work or shear burrs, or both, along the edges which should be removed by machining.

For astmm gripping, it is desirable that the entire length of the serrated face of each wedge be in contact with the specimen.