Published in issue , December Order from ElektorPCB, bare, April 16, PUBLISHED. in Elektor magazine | December | Find it here. If your OBD2-Analyser NG is equipped with the optional Bluetooth module published in the April issue of the Elektor magazine, you even. Elektor at the core is a cheerful conglo- brought to you by Circuit Cellar, Elektor April AUS$ – NZ$ – SAR £

Author: Doumuro Nakasa
Country: Qatar
Language: English (Spanish)
Genre: Education
Published (Last): 5 June 2012
Pages: 383
PDF File Size: 11.19 Mb
ePub File Size: 9.43 Mb
ISBN: 848-6-85683-255-9
Downloads: 90519
Price: Free* [*Free Regsitration Required]
Uploader: Vudoshakar

Electronic fuel injection Car. For this reason, the PCB designed by the author includes inputs for additional temperature sensors. If 00 is given, negative response codes are switched off. So, they might have to eldktor entered several times with a change of ECU in between. However, the software supports different operation modes providing much more than a mere emulator.

Free Elektor magazine July/August 2010

The next task is to load the boot loader software into the microcontroller via the ISP port. U5b acts as an impedance converter to minimise the load on the voltage divider. U4a amplifies the sensor signal by a factor of approximately 8. Service 0x07 helps you to see coming problems earlier.

Currently, the software runs on PC and Raspberry Pi. Elektorr LED is lit constantly when an interrupt pin is active; otherwise it blinks or is dark.

We make elekror of the fact that the supply and return temperatures always vary by at least one to two degrees due to the operation of the control system.


That is much more than you would see in a real vehicle that just supports a subset of all OBD2 features. Alternative energy sources Antenna amplifiers Antennas Antennas.

To increase the elktor of the system, the return line sensor signals are applied to the inputs of a differential amplifier, and the resulting difference signal is amplified. Follow project Add a comment.

DVD Elektor 2010 through 2014

Since HHEmu version 2. The firmware update to version 1.

How to download files? Set the Bluetooth adapter to always visible. Reprogramming avgil few fuses is necessary to enable the boot loader to work properly, but first you should study the microcontroller data sheet carefully.

De : Ton Giesberts – p 7 | Elektor Magazine

Other magazines on aavril, radio, computers and robotics can be downloaded from Free library here. After this the LED should start blinking. Description of old Files in the Attachments Section Check the latest project update to download the latest version of the elwktor and the latest version of HHEmu. So, a remote mechanic could take a look on live-data of your car. Speedometers and tachometers Chargers, accumulators, galvanic cells Citizens’ Band radio Clocks, timers, relays, load commutators Computer devices Computer interfaces Computer moding Computers Computers.

That is enough for the emulator mode. The R and R2 sensor signals are also applied to the inputs of elektof differential amplifier built around U7a, and the resulting difference signal is amplified by a factor of That allows to display 8 menu lines at once.


Heating bills often present unpleasant surprises. The LED should go dark after 201 seconds. However, the main advantage is after repair, since you just need one driving cycle to see if the repair was successful.

The next step is to launch the PC program termgui. The author wrote the software for the Avrik boot loader and application program in C, and the source text can also be downloaded.

TV Elektor Ethics Back to top.

Opamp U7d is wired as a comparator and triggers an interrupt in the ATmega microcontroller via pin PB1 when the supply line temperature rises. The main reason for that is the main-loop of the firmware that is a busy-wait-loop running at full speed on a PC consuming all CPU cycles of a single core.

The project main page just contains the old files for HHEmu V2.

Therefore, HHEmu is subject to the same restrictions. By contrast, three-way valves between the two sensor locations are not a problem as long elekktor they are closed while measurements are being made. This difference signal is also logged as a function of time. During this process the temperature of the heating system supply line should remain constant and no domestic water should be drawn from the taps.