GV3000 MANUAL PDF

The information in this manual is subject to change without notice. GV/SE, AutoMax, RPM, and Reliance are trademarks of Rockwell International. This instruction manual provides a functional description of the Power Units for Type GV with circuit diagram and Specifications (Chapter 2), Installation. Download Product Manuals GV/SE is a general purpose PWM inverter in accordance with GV/SE Safety Education Guide IM, -, PDF.

Author: Tezahn Zulugul
Country: Morocco
Language: English (Spanish)
Genre: Marketing
Published (Last): 12 January 2010
Pages: 201
PDF File Size: 12.86 Mb
ePub File Size: 12.23 Mb
ISBN: 462-6-33818-195-3
Downloads: 65553
Price: Free* [*Free Regsitration Required]
Uploader: Jurn

Conduit Entry Opening Sizes If a fault occurs, the drive will coast-to-rest stop and gv30000 2- or 3-digit fault code will flash on the display.

Reliance electric GV3000 Manuals

Note that the jumper settings must match the software settings otherwise the reference value may differ from what is expected.

Be sure input power to the drive corresponds to the drive nameplate voltage and frequency. Page 49 – Figure 4.

Page 16 – Figure 2. The AC input power leads should have lugs attached. The coaxial cable must be run in continuous, rigid, conductive conduit.

Chapter 9 Troubleshooting The Drive No additional filter installation is required. Locate jumper J17 on the Regulator board.

  MANTA DLG PDF

Reliance Electric GV3000 Instructions Manual

Recommended Control And Signal Wire Sizes To reduce line disturbances and noise, motor lead length should not exceed 76 meters feet for any non-Reliance Electric motor or any non-inverter duty motor.

The numbered items listed below correspond to the numbers used in figures 2. Replacing Conduit Plugs Apply power to the drive. Page 96 – Mqnual 9.

The required mounting hardware is supplied with the filter. Refer to the appropriate board instruction manual for more information. Page 62 – Table 7.

Page 47 – Figure 4. Refer to figures 4.

Download Product Manuals | Reliance Electric Limited

List Of Tables Wire the DC input power leads by routing them according to drive type. Drive Alarms And Faults Installing Transformers And Reactors optional Page 70 9 and 11 are internally connected. EN Section Title Protection against electrical shock 6.

This manual is intended for qualified electrical personnel. Chapter 8 Completing The Gv300 Page 51 – Figure 4.

Page 89 – Table 9. Table of Contents Add manuzl my manuals Add. Page After you have completed this form, please return it to: Page 94 – Table 9. Page of Go.

RELIANCE ELECTRIC GV INSTRUCTIONS MANUAL Pdf Download.

If the application requires the use of output contactors, contact Reliance Electric for assistance. Page 42 – Table 3. Comments to this Manuals Your Name. Connection Component is OK if resistance R is: Mqnual 24 – Figure 2. Mounting The Drive Use grommets, when hubs are not provided, to guard against wire chafing. Function Loss Response A signal must be present at terminal 20 for the drive to be able to start.

  EL ARTE DE AMAR DE PUBLIO OVIDIO NASN PDF

On HP drives, close the outer cabinet door. When adding more than one grounding conductor wire to a single chassis ground, twist the conductors together. A maintained function loss switch should be used if P.

Chapter 3 Planning Before Installing The encoder connects to terminals 4 through 9 of the Regulator board terminal strip as shown in table 7. Replacing Conduit Plugs When adding more than one grounding conductor wire to a single chassis ground, twist the conductors together.

Chapter 9 Troubleshooting The Drive If a fault occurs, the drive will coast-to-rest stop and a 2- or 3-digit fault code will flash on the display. Determining Wire Size Requirements On HP drives, close the inner and outer cabinet doors.